Join our mailing list!


Follow US











You are here: Home > Electronics > Flight Stabilization Systems
Sort By:
1 2
DJI NAZA H Helicopter Stabilization Controller DJI NAZA H Helicopter Stabilization Controller w/GPS
Our Price: $269.99
In Stock
Our Price: $448.00
In Stock
The Naza-H autopilot system is a new platform designed for the helicopter model enthusiast. It inherits the Naza series’ All-in-One design with an inner damping and many other built-in high performance functions (tail gyro, flybarless, and multiple flight control modes) and it also supports D-BUS. The Naza H comes with the main controller module and the LED indicator box for signalling status and flight mode. The Naza M controller features 3 axis gyros, 3 axis accelerometers and a barometer for altitude hold.

The Naza H has modes for manual flying as well as stabilized (self leveling and altitude hold) right out of the box. It also feature easy setup capability including auto trim for flybarless copters.

With the optional GPS module the Naza H gains position hold capability as well as Failsafe position hold to help prevent a crash in the case of loss of RC control. The GPS add on module has both GPS receiver and a 3 axis magnetometer.

From novice to aggressive 3D, the Naza-H perfectly meets the needs of different flying styles. It is not just another FBL controller; it is the best choice for the discerning model helicopter pilot.

The Naza-H autopilot system is a new platform designed for the helicopter model enthusiast. It inherits the Naza series’ All-in-One design with an inner damping and many other built-in high performance functions (tail gyro, flybarless, and multiple flight control modes) and it also supports D-BUS. The Naza H comes with the main controller module and the LED indicator box for signalling status and flight mode. The Naza M controller features 3 axis gyros, 3 axis accelerometers and a barometer for altitude hold.

The Naza H has modes for manual flying as well as stabilized (self leveling and altitude hold) right out of the box. It also feature easy setup capability including auto trim for flybarless copters.

With the optional GPS module the Naza H gains position hold capability as well as Failsafe position hold to help prevent a crash in the case of loss of RC control. The GPS add on module has both GPS receiver and a 3 axis magnetometer.

From novice to aggressive 3D, the Naza-H perfectly meets the needs of different flying styles. It is not just another FBL controller; it is the best choice for the discerning model helicopter pilot.

DJI NAZA H Power Management Unit (BEC) 3DR Radio Telemetry Kit - 915 Mhz (US)
Our Price: $55.00
In Stock
Our Price: $99.99
In Stock
The independent DJI Naza H High Voltage BEC module, with a wide voltage input range (11V-52V) and a variable voltage output (5.8V, 7.4V) can power not only the main controller, but also the servos and receiver. Users can change the output voltage according to their servos, and stable output voltage is provided without an extra battery pack. The use of the BEC makes the aircraft lighter and the voltage more stable, plus less batteries to worry about.

Programmable through the DJI Naza H setup software
Kick your mission planning into real time with 3DR Radios, featuring interchangeable air and ground modules, Android tablet compatibility, and protective cases. 3DR Radios allow your ground station computer to communicate with your vehicle wirelessly, providing unparalleled ease of use for viewing in-flight data, changing missions on the fly, and tuning.
3DR MediaTek MT3329 GPS V2.0 3DR APM 2.6 with Power Module/XT60 (Side Entry)
Our Price: $37.99
(Out of Stock)
Our Price: $159.99
(Out of Stock)
The popular MediaTek GPS now with battery backup for faster warm GPS locks and improved ground plane for improved satellite reception.  Note that the new MediaTek has custom "DIYDrones" firmware that allows the unit to output an efficient and very compressed binary protocol (This firmware is setup for the APM flight controllers). You can still change between NMEA and Binary protocol with standard MTK messages, and switch the refresh rate between 1hz to 10hz, or set any standard serial baud rate (by default is set to 38400 bps and custom binary protocol). The incredible 3DR APM 2.6 Autopilot and Flight Stablilization System.   The APM 2.6 autopilot system is suitable for multicopters and planes and even has firmware for helis and ground vehicles.  A extremely versatile autopilot with a mature software ecosystem including Ground Controls Station and multiple firmwares for specific applications.  Opensource software allows for customization if desired.  This is the 2.6 version with no on-board compass.  Full autopilot and advanced flying modes require the GPS Compass Module.
3DR uBlox GPS with Compass Kit DJI Naza M Lite Multi-rotor Stabilization Controller with GPS
Our Price: $89.99
In Stock
List Price: $209.00
Our Price: $169.00
You save $40.00!
(Out of Stock)
This new design incorporates the HMC5883L digital compass, providing a convenient method of mounting the compass away from sources of interference that may be present in the confines of the vehicle. This is our best GPS module, significantly outperforming the Mediatek GPS due to the larger antenna and next-gen chipset. An excellent solution for multicopters and rovers in particular, where GPS accuracy is paramount. It features active circuitry for the ceramic patch antenna, rechargeable backup battery for warm starts, and I2C EEPROM for configuration storage. The units ship pre-configured for use with 3DR APM 2.6 autopilot.

NAZA M Lite with GPS is a lightweight multi-axis control platform specially designed for aeromodel hobbyists. It is a small all-in-one module. It has S-Bus and PPM support, upgrade support, and extendable port.

Based on the highly successful Naza M the Naza M Lite brings the same performance at a incredible price. The Naza M Lite with GPS features GPS flight mode, Intelligent Orientation modes and Return to Home Failsafe capability.

3DR APM 2.6 with Power Module/Deans (Top Entry) DJI Naza M V2 Multirotor Flight Controller with GPS and PMU
Our Price: $159.99
(Out of Stock)
Our Price: $428.00
(Out of Stock)
The incredible 3DR APM 2.6 Autopilot and Flight Stablilization System.   The APM 2.6 autopilot system is suitable for multicopters and planes and even has firmware for helis and ground vehicles.  A extremely versatile autopilot with a mature software ecosystem including Ground Controls Station and multiple firmwares for specific applications.  Opensource software allows for customization if desired.  This is the 2.6 Top Entry version external compass.  Full autopilot and advanced flying modes require the GPS Compass Module.

NAZA is a lightweight multi-axis control platform specially designed for aeromodel hobbyists. It is a small all-in-one module. It has D-Bus support, upgrade support, and extendible port.

Different from WooKong-M for heavy payloads and aerophotography, NAZA not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability, which gives hobbyists wonderful flight experience.

The new Naza M V2 improves upon the performance of the Naza M and adds features such as Compass self tuning, RTH via switch, advanced IMU calibration, and the ability to interface with the DJI OSD and video transmitters for FPV and video streaming. A great upgrade.

3DR APM Power Module with XT60 Connectors Kit 3DR Airspeed Kit with MPXV7002DP
Our Price: $24.95
In Stock
Our Price: $24.95
(Out of Stock)
The APM Power Module is a simple way of providing your APM with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with XT60 connectors, and wrapped in shrink tubing for protection.

Note: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power servos. Use your aircraft's own ESC/BEC for that.
This is a stand-alone airspeed sensor. Includes Pitot Tube, 1 ft of silicone tubing and 15cm Female to Female Servo Cable.

The MPXV7002 series piezoresistive transducer in the small outline package (SOP) is a state-of-the-art monolithic silicon pressure sensor designed for a wide range of applications, but particularly those employing a microcontroller or microprocessor with A/D inputs. This patented, single element transducer combines advanced micromachining techniques, thin-film metallization, and bipolar processing to provide an accurate, high level analog output signal that is proportional to the applied pressure.

The MPXV7002 is designed to measure positive and negative pressure. In addition, with an offset specifically at 2.5V instead of the conventional 0V, this new series allows to measure pressure up to 7kPa through each port for pressure sensing but also for vacuum sensing (refer to the transfer function in the data sheet for more detailed information).

Pixhawk Advanced Autopilot System 3DR PPM Encoder Board
Our Price: $199.99
In Stock
Our Price: $24.90
In Stock
Pixhawk is an advanced autopilot system designed by the PX4 open-hardware project and manufactured by 3D Robotics. It features advanced processor and sensor technology from ST Microelectronics® and a NuttX real-time operating system, delivering incredible performance, flexibility, and reliability for controlling any autonomous vehicle. Compatible with APM software and easily upgraded using the mission Planner interface APM users are familiar with.
Our new PPM encoder allows you to connect your PWM-only RC equipment to PPM-only autopilot systems, like Pixhawk. Smaller than our previous PPM, our encoder will enable you to reduce all your channels to a single wire, excluding ground and power wires. As a result, you’ll get faster processing and reduced points of error.
3DR PPM encoder includes
PPM encoder module
PPM input cable to PWM receiver DF13 10-position to servo
PPM output cable to autopilot DF13 3-position to servo
DJI 2.4 gHz Bluetooth Data Link (Ipad and Windows GCS and Waypoints) DJI Naza M Lite Multi-rotor Stabilization Controller
List Price: $299.00
Pre Order Price $199.00
You save $100.00!
(Out of Stock)
List Price: $209.00
Our Price: $69.00
You save $140.00!
(Out of Stock)
The DJI 2.4 G 2.4 gHz data modem which can be used for communication with a Ipad or Windows based Ground Control station. Connectivity to Windows can be through a USB connection and with Ipad the 2.4 Bluetooth connection can be used. GCS software and Waypoint license are included.

Flight control systems supported:

2.4G Bluetooth Datalink: ACE ONE, WKM, NAZA-M, NAZA-M V2;
iPAD Ground Station: WKM, NAZA-M, NAZA-M V2;

NAZA M Lite is a lightweight multi-axis control platform specially designed for aeromodel hobbyists. It is a small all-in-one module. It has S-Bus and PPM support, upgrade support, and extendable port.

Based on the highly successful Naza M the Naza M Lite brings the same performance at a incredible price. The Naza M Lite with THE OPTIONAL GPS features GPS flight mode, Intelligent Orientation modes and Return to Home Failsafe capability.

Pixhawk External LED and USB Bluetooth Data link for 3DR APM and Pixhawk
Our Price: $20.00
In Stock
Our Price: $24.99
In Stock
Need an easily visible LED status indicator on your vehicle? Can't get to the USB port of the Pixhawk without disassembly or great difficulty? This kit allows you to remotely mount the status LED and USB port. A must have for builds where the Pixhawk may not be accesable as well as for platforms where you want an easily visible status indicator.such as aerial platforms where the Pixhawk built in LED is not visible when flying.

This kit includes external LED and USB modules to connect to Pixhawk. Use the provided four-position DF13 cables and connect to the I2C splitter module to set up a bright, multicolor LED and convenient USB port for your vehicle.

Includes:

External USB module
External LED module
Two four-position DF13 cables (15 cm)

Connect to your vehicle using Bluetooth! This Bluetooth data link module allows you to connect a Pixhawk or APM autopilot to a Bluetooth-compatible Android device using DroidPlanner or Andropilot ground station apps. Leave your telemetry radio and OTG cable at home, and make a direct Bluetooth connection for pre-flight mission planning and vehicle setup.

Note: This module is intended for pre-flight ground use only. It is not a replacement for an RC transmitter and receiver. The range of the connection is limited to standard Bluetooth range (50 m).


Includes:
Bluetooth module
Pixhawk cable (six-position DF13 to FTDI) 20 cm
APM cable (five-position DF13 to FTDI) 20 cm
DJI NAZA M GPS Upgrade DJI NAZA-H GPS Upgrade
Our Price: $169.00
(Out of Stock)
Our Price: $179.00
In Stock
Naza GPS Add on package. Buy this GPS add on package to add GPS to your current Naza controller. Just update the firmware and add the GPS/Compass and you are ready to enjoy the benefits of the Naza GPS.

Features: RTH (Return-To-Home); IOC (Intelligent Orientation Control) and Low Battery warning.
Naza-H GPS Add on package. Buy this GPS add on package to add GPS to your current Naza-H controller. Adds Position Hold and Failsafe Position Hold capability with more features to come!! The module adds 3 axis magnetometers and GPS sensors. Plug it in , run though the setup process and you are ready to go.
   
 
1 2